Instructions for use

B-FORM

BASE PLATE

B-FORM

Technical information

A compact, rigid sheet that is easy to shape and finish, made of high-density pink styrene. When working with this material, we recommend using one of our B-FORM® thermoforming machines.

PRODUCT FOR PROFESSIONAL USE

Applications

  • Denture bases.

Thermoforming

  • Construct a good plaster model using hard plaster or good-quality 3D resin.
  • The plaster model should not be very tall and should therefore be thinned down as much as possible. The base of the model must have a smooth surface. Remove any parts of the model (vestibule, buccal floor) that may prevent proper thermoforming. Carefully remove any undercuts and round off any sharp edges on the plaster model.
  • The resin model, printed using a 3D printer, should ideally be made as low as possible and in a U-shape (horseshoe shape).
  • During thermoforming, the material always becomes thinner than its original thickness. As a general rule, for every cm of model height, there is a loss of thickness of approximately 20 per cent. For this reason, it is necessary to reduce the height of the model as much as possible or to place the model in the thermoforming machine’s chamber and cover it with stainless steel granules, leaving only the area to be formed uncovered.
  • Heat the disc in accordance with the temperatures and times listed in the section “Temperatures and times”
  • Lower the clamping plate of the B-FORM® thermoforming machine until the heated disc completely surrounds the plaster or 3D resin mould.
  • Apply the vacuum and in a few seconds you will have your bite registration.
  • Allow the newly made bite registration to cool before removing it from the model.
  • To make removal easier, trim the plastic material as close as possible to the edge of the model using scissors and cutters GHOST ALIGNER®.
  • During use of the mouthguard by the patient, it is recommended that it be sanitised daily with the SPORISAN® Gel.

Thickness and size

This sheet is available in the following thicknesses and sizes:

 

SQUARE
125 X 125 mm

 

 

#1819 - Thickness 1,5 mm - 25 pieces
UDI-DI = 8057509250599

 

 

#1818 - Thickness 2 mm - 25 pieces
UDI-DI = 8057509250605

 

 

#1820 - Thickness 2,5 mm - 25 pieces
UDI-DI = 8057509250612

 

Temperatures and times

The temperatures and heating times required to achieve optimal thermoforming are listed below.

  • Thickness 1,5 mm - 190 C° or 116 seconds
  • Thickness 2 mm - 190 C° or 142 seconds
  • Thickness 2,5 mm - 190 C° or 195 seconds

NOTE: The temperatures and heating times listed are for guidance only and have been calculated using B-FORM® thermoforming machines. We recommend adjusting the temperatures and times to suit your requirements.

Symbols


Warnings

In the event of a serious accident, please contact:

  • BART MEDICAL S.R.L. - Telephone: +39 0544 523326 - E-mail: sales@bartmedical.com

FAQs

Would you like to find out more? Read the FAQs about the product.

If the thermoformed sheet does not reproduce all the details of the model, there may be two reasons:
1. The disc has not been heated correctly and needs to be heated further. We recommend following the heating instructions set out in the section "Temperatures and times".
2. The thermoforming machine is experiencing suction problems due to wear and tear on components (seals, vacuum motor) or to excessive dirt build-up in the various filters, which is preventing the air flow from passing through properly.
If the thermoformed sheet shows creases, this means that the disc has been heated excessively and requires less heat. We recommend following the heating instructions set out in the section "Temperatures and times".
To make it easier to remove the sheet, cut the plastic as close as possible to the edge of the template using scissors and cutters GHOST ALIGNER®. For the finishing touches, we recommend using the finishing brush available in 3 different hardnesses (soft, medium, hard).

Manufacturer

BART MEDICAL

BART MEDICAL S.R.L.
Viale Vincenzo Randi 118
48124 Ravenna (RA)
+39 0544 523326
sales@bartmedical.com
www.bartmedical.com

Support

For further information and technical support, please contact us by email at sales@bartmedical.com